What you'll investigate
A single tomato plant can move more than a liter of water from the soil to the air on a hot day, and it keeps less than 5% of that water. Why lose so much? And what decides how fast it goes?
In Part 1 you will learn two measuring skills: finding leaf surface area by tracing leaves on a grid, and counting stomata in a clear nail-polish peel under the microscope to find stomata per mm². In Part 2 you will measure how fast whole plants or cuttings lose water, with a potometer, the whole-plant mass method, or a gas pressure sensor, and compare a control with a fan, a lamp, or a humid misted bag. Then you will design your own experiment on an environmental factor and test it with replicates and statistics.
- ENE-3.D Explain how the behavioral and/or physiological response of an organism is related to changes in its internal or external environment.
- IST-5.A Explain how the behavioral responses of organisms affect their overall fitness and may contribute to the success of the population.
- SYI-1.H Explain how the density of a population affects and is determined by resource availability in the environment.
- 3.C Identify experimental procedures that are aligned to the question.
- 5.A Perform mathematical calculations (areas, densities, rates per unit area, means and standard errors).
- Nail polish is toxic if swallowed or inhaled and irritates eyes. Use it in a ventilated room and keep it away from your face.
- Cut stems with a razor blade or scalpel slowly, away from your fingers, at a 45° angle. Cutting under water keeps air out of the xylem.
- Wear goggles while running experiments. Heat lamps get hot: keep them away from paper, plastic bags, and water.
- If you fill tubing with a syringe, make sure the needle has been removed.
How water gets pulled up a plant
- Transpiration is the evaporation of water from leaves, mostly through stomata. A plant keeps only a small fraction of the water it takes up.
- Water moves from higher to lower water potential (ψ), and the dry air around a leaf has a very low ψ.
- TACT (transpiration, adhesion, cohesion, tension) pulls water up the xylem with no pump.
- Stomata trade water loss against CO2 uptake; guard cells open and close the pore.
- E = g × VPD / P: warm, dry, windy, bright conditions raise the rate; humid air lowers it.
Plants absorb water and dissolved ions from the soil through root hairs by osmosis, diffusion, and active transport. Once water reaches the root xylem, it travels up through stems to the leaves. Most of it then evaporates out of the leaves: this loss of water vapor from the plant surface is transpiration. A plant uses only a small fraction of the water it takes up for growth and photosynthesis; the rest is transpired.
Water always moves from higher water potential (ψ, more free energy) to lower water potential. Soil water is near 0 MPa, leaf cells are more negative, and dry air is extremely negative (around −100 MPa at 50% humidity). That gradient is what drives the whole system.
TACT: how water climbs a tree
The TACT mechanism (Transpiration, Adhesion, Cohesion, Tension) explains how water climbs even a 100-foot tree with no pump. Water evaporates from the wet walls of mesophyll cells into air spaces inside the leaf (transpiration). This pulls on the water film behind it, creating tension (negative pressure). Hydrogen bonds hold water molecules to each other (cohesion), so the pull is passed down an unbroken column all the way to the roots, while water sticks to the narrow xylem walls (adhesion), which helps keep the column from breaking. An air bubble breaks the column, which is why you must keep air out of a potometer and cut stems under water.
Stomata and the leaf cross-section
Water vapor leaves mainly through stomata, pores flanked by two guard cells. Stomata must open to let in CO2 for photosynthesis (and let out O2), so every plant faces a trade-off between gaining carbon and losing water. Guard cells open the pore when they take up K+ and water and swell; they close it in the dark or when the hormone abscisic acid signals drought.
A model for the transpiration rate: E = g × VPD / P
A simple physical model ties the environmental factors together. The rate of transpiration per unit leaf area (E) is a conductance times a driving force:
The driving force is the vapor pressure deficit (VPD): how much drier the air is than the saturated air inside the leaf. Warm, dry air means a big VPD; a humid, misted bag shrinks it toward zero. Water vapor must also cross two "resistances" in series: the stomata (set by how many there are and how wide they open, which depends on light and on the plant's water status) and the thin boundary layer of still, humid air hugging the leaf. Wind strips the boundary layer away, so a fan raises transpiration. Because E is a rate per unit area, you must measure leaf surface area to compare plants of different sizes.
What this simulation models
- Process: Transpiration. Water evaporates from leaves through open stomata, and cohesion and tension pull more water up the xylem.
- Included: Plant species (stomatal opening, leaf area), light (opens stomata; a lamp warms the leaf), air temperature and humidity (vapor pressure deficit), wind, salt, petroleum jelly on leaf surfaces, and soil drying in whole-plant runs. Plants differ, and instruments add reading error.
- Simplified or left out: Stomata respond at once, and leaf warming is a fixed amount. Air bubbles and leaky seals are not modeled. Real potometers often leak or trap air, so real rates are noisier.
Before you start
These questions review key ideas and the calculations you will use in Part 1.
Measure leaf surface area by tracing
Before you begin: Check the grid scale, trace the leaf and record its area in square units (such as mm² or cm²).
Need a quick science reminder?
Area uses square units (such as mm² or cm²), not length units. Use the same scale for every leaf you compare.
Controls
More options
Full procedure
Trace a leaf on graph paper ruled so that 4 small squares = 1 cm² (each square is 0.5 cm × 0.5 cm). Count every square completely inside the outline, then count the squares the edge passes through. Counting each partial square as half a square:
Count stomata in a nail-polish peel
Before you look at any slide: which leaf surface (upper or lower) of a land plant such as bean will have the higher stomatal density (stomata/mm²)? Give a biological reason (1 to 2 sentences).
Controls
More options
Full procedure
Click or tap each stoma (a pair of bean-shaped guard cells) to tally it. Click again to un-mark. Then record the field.
How to make the peel (real lab)
- Paint a patch of clear nail polish at least 1 cm² on the leaf surface you are studying. Let it dry completely.
- Press clear cellophane tape onto the dried polish and peel it off gently by a corner. This is your leaf impression.
- Tape the impression to a clean slide, trim the extra tape, and label the species and the leaf side (upper or lower).
- Scan at low power, then count all stomata in one field at 400X. Count at least three more separate fields. Low contrast? Close the condenser diaphragm a little; no stain is needed.
- Trade slides with two other teams and count theirs the same way.
Density (stomata/mm²) = mean count per field ÷ field area (mm²)
Field area = πr2; here r = 0.225 mm. Average counts from the same microscope field type.
For the slide shown above, take the mean number of stomata per field from your 400X counts and divide by the field area (A = πr², with r = 0.225 mm).
Table 1. Average stomata per mm² of leaf surface (typical values)
Measure the rate of transpiration
Before you run anything: how will each condition (fan, heat lamp, mist + bag, dark) change the transpiration rate compared with the control? Rank them from the biggest increase to the biggest decrease and give a reason (1 to 2 sentences).
Controls
More options
Each plant is a different individual, so expect natural variation. The animation shows the last plant in the batch.
Full procedure
Choose a method, then run the class's agreed control and at least one environmental treatment, with several plants each. For every plant, divide the rate by its leaf area (from the grid-tracing method) so that big and small plants can be compared. Then subtract the control mean to get the adjusted rate.
- Potometer: a fresh cutting (cut under water at 45°) sealed into water-filled tubing connected to a 1.0 mL pipette. As the plant transpires, it pulls water out of the pipette. Read the pipette every 3 min for 30 min after a 10-min equilibration.
- Whole-plant method: a well-watered potted plant with its pot and soil sealed in a plastic bag so only leaves lose water. Weigh it once a day for 4 days.
- Gas pressure sensor: the tubing connects to a pressure sensor instead of a pipette. As water is pulled into the plant, pressure in the sealed tube falls (kPa).
Rate = slope of the readings vs. time. You fill in the last column: rate ÷ leaf area. Numbers are small, so report them ×10−4 (potometer), ×10−3 (pressure), or ×10−2 (whole plant), as the unit says. Example: 0.0118 mL/min ÷ 98 cm² = 1.20 × 10−4, so type 1.20.
Means use the computed rate/area for each plant. Adjusted rate = treatment mean − control mean (same method and plant species). Error bars on the graph are ±2 SE.
Your own transpiration experiment
Pick a question. Some ideas: Which environmental variable affects transpiration the most? Do all plants transpire at the same rate? Is a plant's habitat (moist vs. dry) related to its transpiration rate? Do all parts of a plant transpire? What happens if leaves are fewer or smaller, or if one leaf surface is sealed?
Controls
More options
Collect at least two replicates in two groups.
If p < 0.05, a difference this large would rarely happen by chance alone if the treatment had no effect. Also look at the ±2 SE error bars: when they do not overlap, the difference is likely real.
Make sense of your data
Need to check stomatal counts and leaf measurements? Review that investigation section before interpreting your results.
How do I connect stomata, leaf area, and water loss?
- Identify the comparison. Compare water-loss rates under the same time interval and state which environmental condition changed.
- Account for leaf area. If leaves differ in size, use an area-normalized rate when appropriate instead of comparing only total water loss.
- Interpret stomatal observations. Use your counts or density estimates as evidence, but remember that stomatal number alone does not determine how open the stomata are.
- Consider other influences. Discuss temperature, humidity, airflow, measurement error, and biological variation before making a causal claim.
Connect each conclusion to your own measured values, not only the expected direction of transpiration.